Besarnya Gaya Normal Yang Terjadi Pada Sepasang Roda Gigi Lurus Karena Adanya Tekanan Yang Dihasilkan Roda Gigi Penggerak di Mesin Korin Type Ca-15 Di PT. XYZ
Keywords:
Korin type ca-15 engine, tangential force, normal force, gearsAbstract
PT. XYZ is an Indonesian company engaged in the production of snack foods, including chips, candy, noodles, crackers, and other packaged snacks. This study was conducted at the packing station using a Korin Type CA-15 packaging machine. The objective of this research was to determine the rotational performance of the Korin Type CA-15 machine and to analyze the normal force generated during its operation. The study employed a field research method by collecting primary data directly from the production site. Data were obtained through two techniques: interviews with the production supervisor and machine operators to gather operational information, and direct observations of the machine during production activities. Based on the analysis, the Korin Type CA-15 machine generated a tangential force of 22.639 kgf and a normal force of 24.091 kgf during operation. These results provide an overview of the machine's operating performance and can be used as a reference for evaluating its mechanical condition and operational efficiency.
References
[1] K. Asyarial, H. Jurusan Mesin, F. Teknik, And U. W. Bengkulu Jl Supratman Kandang Limun Bengkulu, “Perancangan Roda Gigi Lurus, Roda Gigi Miring Dan Roda Gigi Kerucut Lurus Berbasis Program Komputasi,” 2013.
[2] B. Bukhari, H. Darmadi, M. I. H. M. Siregar, N. A. Tambunan, And P. E. Hutajulu, “Pengaruh Kuat Arus Pengelasan Smaw Terhadap Kekuatan Tarik Dengan Metode Double Joint Pada Material Baja Carbon,” Momentum, Vol. 19, No. 1, Pp. 69–73, 2023, [Online]. Available: http://vomek.ppj.unp.ac.id.
[3] B. I. Setya Raharja Dan Made Sunada, “Analisa Keausan Roda Gigi Lurus Secara Mikroskopik Dengan Variasi Beban,” 2018.
[4] A. A. Tohari, “Pengaruh Kecepatan Aliran Gas Pelindung Pada Proses Las Mig Material Baja Ss-540 Terhadap Kekuatan Tarik Dan Struktur Mikro,” Vol. 9, No. 1, Pp. 117–122, 2021.
[5] A. Fikri, K. Setiyadi, And M. Mujirudin, “Effect Of Gmaw Welding Current On Penetration Depth And Hardness Of St-37 Steel In Heat Affected Zone Area,” Jurnal Konversi Energi Dan Manufaktur, Vol. 7, No. 2, Pp. 116–122, 2022.
[6] H. Darmadi And S. Safitri, “Analisa Pengembangan Variasi Bahan Papan Komposit Berbahan Dasar Tandan Kosong Kelapa Sawit Diperkuat Polyurethane Terhadap Pengujian Tekan,” In Ready Star 2, 2019, Pp. 117–121.
[7] A. Anggela Sitinjak Et Al., “Pelatihan Teknik Dasar Pengelasan Untuk Meningkatkan Kemampuan Kewiraswastaan Pemuda Karang Taruna Desa Sidoarjo Ii Ramunia, Kecamatan Beringin. Kabupaten Deli Serdang,” J. Apitek, Vol. 1, No. 2, Pp. 7–9, 2022.
[8] H. Darmadi, D. Kurnia, And F. A. Malau, “Besarnya Deformasi Yang Disebabkan Oleh Tekanan Tbr
(Tandan Buah Rebus) Terhadap Poros Bunch Crusher,” Jurnal Mekanova : Mekanikal, Inovasi Dan Teknologi, Vol. 9, No. 2, 2023.
[9] E. W. Silaen, R. Kurniawan Saragih, And J. Huatabrat, “Analisis Pengujian Penetrant Pada Pengelasan Gmaw Baja Karbon Rendah,” In Konferensi Nasional Social Dan Engineering Politeknik Negeri Medan, 2023, Pp. 828–837.
Downloads
Published
Issue
Section
License
Copyright (c) 2024 Yanto
This work is licensed under a Creative Commons Attribution-NonCommercial-ShareAlike 4.0 International License.
