Perhitungan Oil Losses Pada Ampas Press di Proses Pengepresan Unit Screw Press PT. XYZ
Keywords:
Mass Balance, Oil Losses, Screw Press, SoxhletationAbstract
This research was conducted at PT. XYZ. Oil losses are the percentage of oil that is absent or not included in the subsequent oil processing process but is included in the waste process. The aim of this research is to determine the percentage of oil loss contained in press dregs using the soxhletation extraction method. Based on the results of mass balance calculations, it was obtained that the number of components entering the screw press was 22,401 kg/hour of digester chopping and 6000 kg/hour of delusion water. The number of components coming out of the Screw press, namely press dregs, is 8,400 kg/hour and Delution crude oil is 20,001 kg/hour. The results of this research show that the oil losses obtained during the pressing process were 4.45% or 373.80 kg/hour. This is in accordance with factory standards where oil losses are 4-6%.
References
[1] H. Darmadi, A. N. Savitri, And D. Halawa, “Besar Tegangan Geser Yang Terjadi Pada Shaft (Poros) Akibat Putaran Mata Pisau Untuk Mencacah Berondolan Pada Unit Digester Pt Z,” Atds Saintech-Journal Of Engineering E-Issn2023, Vol. 4, No. 2, Pp. 17–23, 2023.
[2] H. Darmadi, M. Muttaqin, K. A. Tambunan, And R. A. Barus, “Kekuatan Dan Daya Tahan Pegas Terhadap Getaran Bandul Pada Vibrating Screen Di Stasiun Pemurnian Pks Pt. X,” Jurnal Mekanova, Vol. 8, No. 1, Pp. 73–85, 2022.
[3] A. Purba, B. Bukhari, And A. Nurya Savitri, “Pemotongan Daun Worm Screw Setengah Lingkaran Untuk Mengurangi Broken Nut Pada Statiun Press Pt X,” Juvotek, Vol. 1, No. 1, Pp. 17–23, 2023, Doi: 10.12345/Xxxxx.
[4] M. Haris, G. Supriyanto, And H. Hermantoro, “Pengaruh Tekanan Press Dan Umur Screw Terhadap Kehilangan Minyak Kelapa Sawit (Oil Losses) Di Stasiun Press,” Agroforetech, Vol. 1, No. 1, Pp. 654–662, 2023.
[5] H. Saputra And A. Susilawati, “Analisa Effectiveness Dan Oil Losses Pada Mesin Screw Press Serta Implementasi Kaizen (Continues Improvement) Untuk Peningkatan Proses Produksi Di Ptpn V Sei Garo,” 2018.
[6] N. Nelza, D. Christine Silowaty Purba, A. Nurya Savitri, And L. Syarah Siregar, “Perhitungan Neraca Massa Pada Unit Screw Press Di Pt. Xyz,” Juvotek, Vol. 1, No. 1, Pp. 32–39, 2023
[7] Y. A. Matondang, B. Harahap, And S. R. Sibuea, “Analisis Kehilangan Minyak Sawit Pada Mesin Screw Press Dengan Metode Statistical Process Control Di Pt Pp London Sumatera Indonesia Tbk,” Blend Sains Jurnal Teknik, Vol. 2, No. 1, Pp. 56–64, Jul. 2023, Doi: 10.56211/Blendsains.V2i1.252.
[8] M. Taufik Siregar, Z. Effendi, B. Mulyara, F. A. Lubis, T. Pengolahan, And H. Perkebunan, “Analisa Persentase Kehilangan Minyak Sawit Pada Ampas Press Di Ptpn Vi Unit Usaha Solok Selatan Analysis Of Palm Oil Losses Percentage In Press Waste At Ptpn Vi Business Unit Solok Selatan,” Agro Fabrica, Vol. 5, No. 1, Pp. 14–21, 2023.
Downloads
Published
Issue
Section
License
Copyright (c) 2024 Rosmiati Rosmiati, Dian Kurnia, Sorta Lumbantoruan
This work is licensed under a Creative Commons Attribution-NonCommercial-ShareAlike 4.0 International License.
